Installing a Trimetric Battery Monitor

Started by LJ-TJ, March 01, 2015, 08:12 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

LJ-TJ


Installing a Trimetric Battery Monitor:

The idiot light panel is almost (but not quite) worthless for monitoring the condition of your house battery or batteries.  It uses voltage levels to change the color of the lights.  You can use a volt meter to do a slightly better job, but the problem is that unless the battery is sitting with no load for a period of time, the reading will not be accurate.  And your battery always has some load unless you have disconnected it. You can use a hydrometer and check each cell for an accurate reading, but that is a pain, and impossible if you have sealed batteries.  The easiest way to keep track is a battery monitor that does more than measure voltage.  After reading up on the options, we settled on the Trimetric.  It was said to be easier to set up and use than monitors of similar capability. We got our Trimetric 2025RV from Randy at www.BestConverter.com.  Randy is very helpful answering questions and giving advice. The Trimetric comes with a display unit, a shunt, and a very long cable.  And a lot of instructions.
The shunt looks intimidating, but it is not hard to install.  The shunt is necessary to get current readings.  The cable is long enough for the largest Class A, we just left the excess coiled up in a storage compartment. We found the wiring diagram for the Trimetric to be rather confusing, so we later drew our own version of it to hopefully be a bit clearer than the one with the instructions:      
Step 1.  Find a place near the battery to install the shunt.  Depending on the location of your battery (or batteries) this may be easy or difficult.  In our case there was room just outside the battery compartment which is a vented compartment under the driver’s side dinette seat.  We drilled two holes for the cables.   These holes were later sealed so any battery gases would vent through the proper vents rather than into the coach. The radio rear speaker and the propane detector are also in this area.   
         
Step 2: The shunt is installed on the negative side of the battery.  That means that the cable (or cables) currently going to the negative terminal (or terminals) on the battery with go to one side of the shunt and you will add a new cable from the other side of the shunt to the negative post on your battery. You will need to buy at least one additional length of battery cable to go from the negative terminal on the battery to the shunt.  If the negative cable currently going to the battery is not long enough to reach the shunt, you will need to replace it.  Various lengths of battery cables are available at auto parts stores and online.  Measure to see how much you need.  You should keep cables as short as possible.         
Inside the battery compartment you can see the new cable for the shunt exiting the battery box. You can also see the red wire from the Trimetric wiring harness attached to the positive terminal.  (See Step 4).  It is mounted to the same post as the heavy white wire providing 12 volt power used for starting the Onan generator. This is a Group 24 deep cycle Exide battery.  It is only 80 amp hours.             


Step 3:   You will need to locate the display in some visible location.  Pick a place it will be easy to run the wiring harness to.  We mounted ours on the back of the pantry cabinet above the TV.  You will have to drill one or more holes to run the wiring harness After adding a solar panel we put the monitor for the solar controller next to the battery monitor.  It is very interesting to see the amps generated by solar and the amount going into (or out of) the battery at the same time.               


Step 4:  The diagram for the wiring is not as complicated as it first appears.   There are 4 wires â€" one white, one red and two black.  One end of the cable has connectors on the wires.  Remove the fuse before connecting the wires.
1.     The red wire with the fuse and the big end goes to the positive terminal of your house battery.  So it needs to go inside the battery compartment.
2.     The white wire goes to the small terminal on the side of the shunt that connects to the negative battery terminal.
3.     Both black wires go to the small terminal on the opposite side of the shunt.     


Step 5:  Route the wires to the display.  This is probably the most time consuming step â€" depending on where you located the display.  Leave the extra wire coiled up somewhere out of sight or shorten the cable if desired. We fished the cable up from the dinette storage compartment behind the wall panel into the pantry cabinet.           


Step 6:  At the Trimetric display the terminals on the circuit board are labeled. 
1.     The red wire goes to the B1+ terminal
2.     The white wire goes to the SIG terminal
3.     One black wire goes to the G1 terminal and the other goes to the G2 terminal.  It does not matter which wire goes to which terminal since they both go to the same side of the shunt The B2+ terminal is extra â€" you can run a wire up to your engine compartment if you would like to monitor the voltage on your engine battery.  It will not give any other info other than voltage about this second battery       


Step 7:  Check your connections and then install the fuse.  You now have to program the unit.  It needs to know your battery’s capacity and some other info in order for it to provide you with accurate information.  The basic required information is P1, P2 and P3.  P1 will be 14.4 volts (bulk charging voltage), and P3 will be the capacity of your battery in amp hours.  Ours is 80 amp hours.  If you are running two 6 volt Trojans you could be at 220 amp hours.  P2 is computed from the other numbers as the manual states.  Entering these values is a bit like figuring out how to set a new multi-function watch.  You will likely mess it up a couple of times before getting it right. Depending on what we are doing we may leave the display on % Full or we may leave it on Amps (in or out).  You can display voltage and watts as well. We have been very pleased with the usefulness of the Trimetric. Hm?         

Oz

I'd like to add that Dave Bailey made note in the Gear Box that he purchased one of these to install on eBay:


http://www.ebay.com/itm/180957166631?_trksid=p2060778.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT


He said it was cheaper, but I assume it serves the same function.
1969 D22, 2 x 1974 D24 Indians, 1977 27' Itasca

DRMousseau

I jus installed one of these last weekend, along with a new "Boondocker" and two new T-105's....oh, and I replaced my broken hydrometer too.

A through understanding of how something works, can allow you to use systems like this to a greater advantage that's far beyond the average user. Such advantage can extend the life of batteries and systems, and actually reduce costs! While the Tri-Metric IS a bit more costly, and may be a bit more more "high-tech" than other devices, it does save considerable time in monitoring, measuring, and record keeping, as it stores AND provides information helpful in maintaining a healthy battery system in your RV.

Most monitors display battery voltage in some way, and I'll agree that most are are quite poor, inadequate, and often useless. Some display battery capacity remaining, and tell your when it's low or time to "charge", based on voltage alone. The basic information displayed by the TriMetric, is much the same as any battery monitor, but much more accurate and precise due to "programming" of additional "set points". This provides capacity and charging info based on YOUR specific system!! The extended information and data capabilities, also help in monitoring and maintaining your system with maximum benefits.Oh I'll still get to the batteries monthly, to take hydrometer readings and adjust water levels. And this added effort will also allow me to "adjust" programed set points as needed. The extended information and data capabilities, also help in monitoring and maintaining your system with maximum benefits for both, the user AND service technicians who may be servicing and troubleshooting your system.

Did you know,.... batteries, such as the T-105, actually INCREASE in available capacity from new condition??? As the new internal plate surfaces are eroded by use, the surface area increases and provides more storage capacity for use!!! By carefully monitoring batteries, you can take advantage of this increased capacity AND actually prolong battery life. If your batteries are not used to their full capacity on a regular basis, you will actually REDUCE your battery life and potential!!!

Yes,... the Tri-Metric Battery Monitor is a bit more costly. But so are batteries when they fail unexpectedly!
Welcome,..
To The Crazy Old Crow Medicine Show
DR Mousseau - Proprietor
Elixirs and Mixers, Potions and Lotions, Herbs, Roots, and Oils
"If I don't have it,... you don't need it!"