Classic Winnebagos & Vintage RVs

Topic Boards => Dodge - Chrysler Chassis => Topic started by: rustyescott1 on July 06, 2015, 05:12 PM

Title: Drag link swap?
Post by: rustyescott1 on July 06, 2015, 05:12 PM
does any one have any info for the sterring parts for all the differant chassis m300-m600? namely the drag link.
Title: Re: Drag link swap?
Post by: DaveVA78Chieftain on July 08, 2015, 10:09 PM
Quote from: rustyescott1 on July 06, 2015, 05:12 PM
namely draglink
Do you have a 72 M300 or M375 chassis?
Title: Re: Drag link swap?
Post by: Elandan2 on July 09, 2015, 07:34 AM
This is a link to the Spicer catalog.  Page 28 and 29 have Dodge part listings.  You may be able to find what you're looking for here.


http://spicerparts.com/sites/default/files/pdf/hx701-10-2013.pdf (http://spicerparts.com/sites/default/files/pdf/hx701-10-2013.pdf)


Rick
Title: Re: Drag link swap?
Post by: rustyescott1 on July 09, 2015, 09:48 PM
ok here is what i have i have been given a 1978 executive motorhome that is in very good shape , but is missing the front axle . it had the big lug pattern 5lug the one that is hard to find wheels for. i have the front axle out of my 69 winne that i can put under it . the only thing i can't find out if the draglink willinterchange.
Title: Re: Drag link swap?
Post by: DaveVA78Chieftain on July 10, 2015, 07:09 PM
5 lug means you have a M500 chassis on the 78 that has an axle rated for 5000lbs.

For the 69
If a M300 chassis, it is rated for 3800 lbs
If a M375 chassis, it is rated for 4000 lbs.
Neither one is actually rated for the weight the M500 chassis is designed to support.

Dodge did not increase the weight ratings until 72/73
M300/RM300: 4500lbs
M400 (RM350) / M500 (RM400): 5000lbs.

Draglink
76-78 M300/M400/M500: Dodge P/N 4026505
74/75 M300: Dodge P/N 3637091
74/75 M400 (RM350) / M500 (RM400): Dodge P/N 3780545
My parts book does not list the 69 M300/M375 part numbers (starts at 73)

Different parts for different axle sizes

78 M500 used Saginaw steering gear
69 is not clear and may have either a Ross or Saginaw steering gear.

Dave
Title: Re: Drag link swap?
Post by: DaveVA78Chieftain on July 10, 2015, 10:34 PM
On further thought,  a 78 M500 uses disk brakes with hydroboost.  69 used drum brakes with a vacuum booster. 
Master cylinder is different (front disk/rear drum vs front/rear drum)
Disk setup has a proportion valve designed to hold off applying pressure to the front disk caliper to allow the rear brake shoes to overcome spring pressure and engage the drum.  If you install front drums then the front wheel drums not be in sync with the rear drums.

Dave
Title: Re: Drag link swap?
Post by: planetcharlie on February 02, 2019, 08:28 PM
Iââ,¬â,,¢m in desperate need of a part for my 1973 Winnebago Brave D20. I believe it has a dodge m300 chassis and a 318 v8 motor. I need a ââ,¬Å"drag linkââ,¬Â because my steering is very loose. Itââ,¬â,,¢s 24 inches long. The manuals I got only showed it on one page of the parts catalog, but when I google searched the part number nothing came up anywhere. The service manual didnââ,¬â,,¢t even mention a drag link at all. Perhaps it was called something different back then? It doesnââ,¬â,,¢t even show up in any of the diagrams in the exact area it would be in? Could I have my chassis model wrong? Iââ,¬â,,¢ve called parts places all Iââ,¬â,,¢ve the us and nothing. I ordered two that people said were correct, they looked right but were the wrong length. Maybe itââ,¬â,,¢s the same as another dodge truck model and I could order one of them? Itââ,¬â,,¢s a part that wears out frequently so a salvage yard would likely have ones worn like mine. Any help would be great! Perhaps you can help me post this where other classic Winnebago owners can see it and help. Thank you!
Title: Re: Drag link swap?
Post by: Froggy1936 on February 02, 2019, 10:45 PM
If the parts you have, Have the correct ends and are adjustable on either end for slight length differences you can modify the length by cutting and splicing a piece of non galvanized pipe ,welded in , It will take a little Engineering And a professional weld .   A template from the original (drawing) would help ! Frank
Title: Re: Drag link swap?
Post by: postman on February 03, 2019, 01:23 AM
I'd give Orielly Auto Parts a shot cross reference D300.
Title: Re: Drag link swap?
Post by: thomas on February 03, 2019, 02:13 PM
HEY!! PLANET  CHARLIE!!  did you see all the posts about drag links above  your posts??  from back in  2015?? D:oH!
Title: Re: Drag link swap?
Post by: planetcharlie on February 07, 2019, 02:43 AM
Quote from: thomas on February 03, 2019, 02:13 PM
HEY!! PLANET  CHARLIE!!  did you see all the posts about drag links above  your posts??  from back in  2015?? D:oH!


Yes, but none of them found it for me. I didnââ,¬â,,¢t try weld one to size yet because I still think I should be able to find one thatââ,¬â,,¢s the right size?
Title: Re: Drag link swap?
Post by: Elandan2 on February 07, 2019, 10:03 AM
Try this site there are a few drag links about the length you are looking for specified for Dodge trucks.


https://www.danaaftermarket.com/commercial-vehicle/commercial-axle/steering-drag-link/list?cat1=311&cat2=339&cat3=336&filters=%5B%22DODGE%22%5D&filterObject=%5B%7B%22name%22:%22General%20Application%22,%22type%22:%22STRING%22,%22values%22:%5B%22DODGE%22%5D%7D%5D&sort=1



Title: Re: Drag link swap?
Post by: thomas on February 07, 2019, 06:31 PM
sure is nice to "click" instead of typring in that adress!!!///!!!
Title: Re: Drag link swap?
Post by: planetcharlie on February 07, 2019, 11:08 PM
Quote from: Elandan2 on February 07, 2019, 10:03 AM
Try this site there are a few drag links about the length you are looking for specified for Dodge trucks.


https://www.danaaftermarket.com/commercial-vehicle/commercial-axle/steering-drag-link/list?cat1=311&cat2=339&cat3=336&filters=%5B%22DODGE%22%5D&filterObject=%5B%7B%22name%22:%22General%20Application%22,%22type%22:%22STRING%22,%22values%22:%5B%22DODGE%22%5D%7D%5D&sort=1 (https://www.danaaftermarket.com/commercial-vehicle/commercial-axle/steering-drag-link/list?cat1=311&cat2=339&cat3=336&filters=%5B%22DODGE%22%5D&filterObject=%5B%7B%22name%22:%22General%20Application%22,%22type%22:%22STRING%22,%22values%22:%5B%22DODGE%22%5D%7D%5D&sort=1)


Thank you. Iââ,¬â,,¢m checking with them now.
Title: Re: Drag link swap?
Post by: planetcharlie on February 11, 2019, 06:35 PM
Quote from: planetcharlie on February 07, 2019, 11:08 PM

Thank you. Iââ,¬â,,¢m checking with them now.


I found the drag link that fits my 1973 Winnebago Brave ! I got it at oriellys auto parts after they cross referenced every link with the length I needed. Itââ,¬â,,¢s moog DS881.


Thank you all for your help!
Title: Re: Drag link swap?
Post by: SR66 on July 12, 2019, 04:40 PM
The Moog DS881 is the correct length. Unfortunately the studs are larger and won't fit thru the holes on the pitman arm and steering knuckle.


I am still on the search for one that will work.
Title: Re: Drag link swap?
Post by: Rickf1985 on July 12, 2019, 06:31 PM
You can have the holes reamed out the correct size to fit the larger ends if it comes down to that. It is not that hard of a job and only take a couple minutes. But it is permanent so if you do it make a note somewhere that it was done and the correct part number for the drag link.